Junked 1990 Volvo 740 GL with Cerma Engine Treatment

Came in 2nd place in the Terryville Fair Demolition Derby (2015).   From James McGrath:  www.CermaLube.com  (203) 376-1152

EVIDENCE of Efficacy... usher the new technology in!   From Veloster Forum and Senior Member, Peter K.  Indianapolis.

OLD technology (non cerma motor oil) uses detergents, and attempts to keep carbon in solution (emulsified). This suspended carbon is way too small to be harvested by even the best of over the counter oil filters -- any brand. None of them filter finer than 40-45 microns.

Cerma Attends Auto Fest with Josh Borne

Josh - "CERMA IS POSITIVELY AMAZING!"

Josh Borne is a championship freestyle competition performer, a premier professional freestyle extreme athlete, and a world renowned competitor on the XDL Championship Sportbike Freestyle Series and multiple other circuits.  Borne has traveled across the nation and around the globe showcasing his high energy talents to crowds of all ages.

Cerma Attends 2015 NYC Fleet and Equipment Show at the Unisphere...
Cerma STM-3, while extending oil drain intervals, continues to provide protection...
To fix this common problem and reduce the noise caused by issues with the lifters...
If engine is losing oil and the engine is not broken, the motor oil is not doing it job in this "closed" system...
Cerma STM-3 Fuel Treatment Promotion.  Increase Power, Improve Performance...
Protects like a 40W, runs like a 0W.  Cerma Releases EVO Motor Oil, the most advanced motor oil on the market today...
In a perfect world, facilities would operate the same vehicles, of the same age, under the same operating conditions...
99 miles on the engine treatment, less engine noise, quieted the hpfp...
Can be used in all 4-stroke motorcycle engines, including racing, high performance, street, and off road motorcycles...
Government mandated reductions on Zinc and Calcium levels in motor oils has gradually removed...
Due to deteriorating piston seal o-rings, vanos units have been consistently diagnosed...
Veloster Forum, 205 pages and counting, all the information you need and then some...
Cerma CSL Firearm Foam and Grease,  Improved formula with STM-3 Technology

 

Diesel Semi-Truck

Just a quick note to tell you what Cerma has done for my trucks.

We put Cerma in the whole system of one truck with 798,000 miles, (engine {470 Detroit}, transmission, and both rear axles). Within 50 miles 95% vibrations were gone, stack smoke was all but gone, and pulling first ...

Everett Schaffer Co Owner E & C Transport, Inc / Terminal 74 for Ace Transportation Houma, Louisiana Sunday, January 28, 2007
Subaru Legacy 1997 Wagon

I have purchased 2oz of CERMA engine treatment with STM-3 and got a free 2oz of Fuel Treatment. Thank you for the gift! Vehicle is: Subaru Legacy 1997 Wagon , VIN: xxxG5LJ4WG08xxx, European version, 2.0lt. Engine, AWD, NON Turbo. Mostly driven on LPG(85-90% of the time)!!!

I ...

Ivo K. Subaru Legacy 1997 Wagon Tuesday, September 1, 2015

I just want to state that other than an amazing product, this company has amazing customer service. The day after ordering my engine treatment I received a call to inform me that I did not need a full 2oz, and then they asked to change my order to a 1oz and refund a portion of my ...

Tyler Conklin 2016 Hyundai Veloster Turbo Friday, September 16, 2016
ReachMe

CERMA is the real deal! If you follow the instructions after applying product to your oil, you will notice less noise, better fuel economy, about 1.5 miles more per gallon! Add to your dirty oil with about 2k miles before you have to change it again. This stuff works, and works ...

ReachMe Happy Customer Sunday, September 28, 2014

Re-post from:http://www.velosterturbo.org/forum/veloster-maintenance/5282-cerma-treatments-oil-lubricants-good-order-222.html#post353642
02-23-2016, 10:09 AM

I will say I'm only 2 days into the treatment with 22k miles on the odo only 100 miles driven since treated and already ...

Sly4c Thursday, March 10, 2016
2007 Toyota Avalon

Just treated my 2007 Toyota Avalon with the Cerma Engine Treatment and the Cerma Transmission. Car is running smoooooth (the vibrating is down to almost zero)- thanks Cerma. The engine also had a slight miss when I accelerated. Already noticed a significant improvement and I'll ...

Dave P 2007 Toyota Avalon Friday, April 3, 2015
Pick-up Truck

I recently stopped in at my local gas station to fill up like I do twice a week when I met the attendant (Ken Briscoe). We got to talking passing time while I was filling up when Ken asked me if I had ever heard of a product called cerma. I told him that I hadn’t so Ken gave me ...

C. Green Truck with over 105,000+ miles Tuesday, August 31, 2010
223,000 Miles

Engine Treatment: Added CERMA and gas mileage has increased and harmonics are much better. Love to drive my car more than ever. Bought a car with over 223,000 hard miles. Added CERMA and gas mileage has increased and harmonics are much better. Love to drive my car more than ever. ...

Scott S. 223,000 Miles Tuesday, September 29, 2015
1990 560 SEC Benz

I never bother writing reviews, however, this product is FANTASTIC!! 560 SEC Benz with 113k miles, about 30k since valves...UNBELIEVABLE!! Cold start on 1st turn of starter EVERY time, not the 4-6 turns... After the results with oil treatment, did tranny, power steering and fuel ...

Pdidheon 1990 560 SEC Benz Monday, March 23, 2015
Alliant Energy

We have used Cerma in a gear box which is 1 of 2 identical units. The one
we treated was initially running 60 decrees hotter than the other one. We want them to
run at no more than 180 degrees. The manufacturing company tried changing out the
gears and in essence did everything ...

Eric Krahenbuhl Alliant Energy, Emery Generating Station Monday, July 16, 2012
Jeep Grand Cherokee

I purchased a 1996 Jeep Grand Cherokee with 196,000 miles on it. The transmission was beginning to act up after a couple of months driving the vehicle. What was happening was when the Jeep was shifting into over drive at 50 miles an hour it was not as smooth as it should be. After ...

Ron R Jeep Grand Cherokee Sunday, April 15, 2012

I've already used Cerma STM-3 Engine Treatment on 1 vehicle and plan to use this shipment to do a second. Great product, great support. I love this product, and keep buying it when I discover a friend or acquaintance who needs it too. Thanks! – Stephen Wild Post 2 (04/13/2012, ...

Stephen Wild Jeep Grand Cherokee Friday, April 13, 2012
1991 Ford Tempo

I am a journeyman machinist/machinery mechanic automotive enthusiasts with 40 years of formal and trade experience.presently I am rebuilding/upgrading a 1991 ford tempo and writing a book.during upgrade research i found about Cerma.as it is a coating, i was EXTREMELY concerned about ...

Bill 1991 Ford Tempo Thursday, September 15, 2011
Yanmar Tractor

I was a skeptic, but when I added the Cerma Engine Oil Treatment to my Yanmar, the change was amazing! Within 20 minutes the engine smoothed out, became much quieter, and is clearly running much better. I can pull an extra 300-400 rpm – that means more horsepower out the shaft – without ...

Chuck W. Yanmar Tractor Thursday, September 3, 2015

Just received the engine treatment and it works perfectly :)

My car has more torque, sounds great it's also smoother running.
My vtec kicks @ 6k and pulls through all gears perfectly. I need to replace my timing chain and I'm sorry I didn't change it before using the cerma.

So ...

James T. (UK) 2003 Type R Honda Civic EP3 with VTEC Engine and 114,500 miles Monday, March 10, 2014
Mack 350

This stuff is crazy good although I need to replace injection pump on my Mack 350. This product made the truck run the best it has done for a year. Almost made me forget the pump. Suggestions for a new pump? -- Peter P. via Amazon (Verified Purchase)

Peter P. Mack 350 Sunday, July 24, 2016
.357 Sig Semi

I used the Cerma foam treatment in the following handguns: .44 revolver, .357 revolver.40 semi, .357 sig semi and AR 15 .223 rifle so far. I am very pleased with the results of all barrels. Next shooting session only required the use of bore snakes to clean the small amount of debris. ...

Dale W. .44 revolver, .357 revolver.40 semi, .357 sig semi and AR 15 .223 rifle Wednesday, October 7, 2015

I put Cerma Trans in and have noticed the trans shifts better and the temp gauge is reading cooler.

– Drew (10/25/2012, 09:35 PM)

Drew Challenger RT Thursday, October 25, 2012
Pontiac Formula

I bought a bottle of Cerma on the recommendation of a friend at work. My 2001 Pontiac Formula had a lifter tick that I was hoping to get rid of. After putting in the Cermax and letting the engine run for 5 minutes, the tick was GONE! He later asked me if my car had more power, but ...

Richie 2001 Pontiac Formula Thursday, August 12, 2010
2004 Ford F350 6.0

Works. 'Lil spendy but damn worked. Bought In april 2014 used in my '04 6.0 F350 4x4 an put some in my dad's dodge '05 3500 5.9 he even commented + on this, wish could afford more often tried others this works the best for me an my 6.0. Great product the Diesel fuel treatment better ...

D. Watson 2004 Ford F350 6.0 Tuesday, March 8, 2016
Lexus IS

John,
I applied the product to my Lexus, and I could tell and real difference in power. If I can get my right foot to cooperate, I bet I’ll see fuel savings. I just wanted to let you know. REALLY COOL! --Dennis B
received via e-mail at cermaceo@gmail.com (Nov. 12 2010)

Dennis B 2007 Lexus IS 350 Friday, November 12, 2010

This product saved me from loosing the use of my furnace for a week in December, I was leaving my home in north IA. I heard a strange noise from the basement and went to investigate, it sounded like a bad bearing, I opened the case of the furnace and it got louder, shut furnace off ...

James, VAS-PRO 11 year old furnace Thursday, July 26, 2018
Carbide Chain Saw

I think we performed a pretty significant experiment with your product today. My training officer did not return to the office but I will get more information tomorrow. We took 2 identical roof cutting carbide chain saws and had the same operator on the same roof make cuts one after ...

Chief Doug Carbide Chain Saws Wednesday, April 1, 2015
40 FT Meridian Yacht

The boat is going over 28 MPH. Granted clean bottom and props but I don’t believe it ever went over 26ish on this boat. It is a 40 FT Meridian Yacht weighing 17 tons. Top end speed was increased about 10% and that is before we start with the CERMAX Motor Oil.

Leigh Overland 40 FT Meridian Yacht Wednesday, June 4, 2014
2015 Volvo Day Cab

I just wanted to tell you about my Volvo semi that I drive. It is a 2015 Volvo Day Cab with A/T. It now has 39,500 miles on it. I treated it at about 10K and fuel economy increased even though it was a new truck to about 4/10 mile per gallon. When the oil was changed by the company ...

Chad S. 2015 Volvo Day Cab with A/T Tuesday, September 29, 2015

In my application, 1991 BMW 750i 5.0L 12 cylinder, I was mainly trying to correct annoying hydraulic lifter noise without having to replace any lifters. The Cerma product worked almost immediately to quiet all noisy lifters and they have remained quiet for the last 30K miles on an ...

Mark C. McCafferty, P.E. 1991 BMW 750i 5.0L 12 cylinder Tuesday, February 18, 2014
2002 Toyota Sienna Minivan

I used Cerma STM-3 Engine Treatment in my 2002 Toyota Sienna Minivan; Fuel mileage went up from 260 mile per tank to 355 miles extremely happy with gas saved. I also used Cerma in my 2000 Dodge Caravan SE; Fuel mileage went up from 245 miles per full tank to 350 miles now. Lastly, ...

OKTAY TUZER 2002 Toyota Sienna Minivan Wednesday, March 7, 2012
  • Cerma STM-3
    Technology and
    Information

    Learn More
  • Cerma Motor Oil
    Technology and
    Information

    Learn More
  • Cerma Blue Ice
    Technology and
    Information

    Learn More